Linear Gate Motor & Opener Nationwide

Linear Gate Motor & Opener in Frisco: What to Know First

We repair and install Linear gate motors and openers across Frisco, and most jobs are diagnosed on the first visit. Linear swing-arm and slide operators share certain failure patterns we see repeatedly in this area, which means we can usually give you an exact written price before any tool comes off the truck. If you have a Linear gate that won’t open, opens halfway, or grinds when it moves, call (940) 290-7996 and tell us what the gate is doing. We’ll tell you what it costs to fix it.

Call (940) 290-7996

This page is for owners of Linear swing gates and slide gates in Frisco: the ACT-34B, the LRA series, the SWR and SLR slide operators, and older PRO-series units that are still running on original boards. We are an independent Linear service provider, not a factory warranty station. That matters when you need a board-level repair or a decision about whether to pay Linear’s OEM part price versus a quality aftermarket equivalent.

How Linear Products Fail - and How We Fix Them

• Limit switch drift on the LRA swing-arm series. The LRA uses mechanical limit cams that creep over time, especially on gates that cycle more than 60 times a day. The symptom is a gate that stops short of the closed position by six to twelve inches, or reverses immediately after hitting the close limit. We reset the cams, torque the locking nut to spec, and photograph the new positions so the next adjustment doesn’t start from guesswork.
• ACT-34B control board failure from Texas lightning. Frisco gets storms that send voltage spikes down the AC feed to the gate. The ACT-34B’s power supply section eats that spike first, and the board will show a dead display or a blinking alarm with no motor movement. We test the transformer output, confirm the board is the fault, and replace it with either OEM or a proven aftermarket board depending on the unit’s age and the customer’s preference.
• Gearbox wear on LINEAR SLR slide operators. The SLR runs a chain-drive gearbox that goes dry inside when the factory grease hardens. The gate still moves, but the motor labors and the chain chatters under load. In Starwood, where some driveways run 40-plus feet of gate travel, this shows up faster. We re-grease the gearbox when the unit is salvageable, or replace the gear set when the teeth are showing wear. We’ll show you the photos either way.
• Photo-eye misalignment on gates near storm-drain settling. Most Linear safeties are retro-reflective photo-eyes, and Frisco’s shifting clay soil tilts fence posts enough that the beam drifts out of alignment. The gate reverses mid-cycle or refuses to close at all. A photo-eye is the infrared beam that stops the gate if something crosses the path. We set the beam, clean the lens, and mark the bracket position with a paint dot so you can see exactly where it should sit.
• Dead transformer batteries in Linear battery-backup setups. Linear’s battery-backup swing units use two 12V sealed lead-acid batteries that fail silently at the three-to-five-year mark. The gate works on AC but stalls or creeps on battery test. We load-test the batteries, replace them as a pair if one has failed, and record the date code on the new batteries in your service file so you know when they’re due again.

Our Linear Gate Motor & Opener Process

Every Linear job follows the same field-report discipline Adrian Vance has used since 2014.

1. 1
   Phone triage. We ask what the gate does when you press the remote, when it started, and whether any recent lightning or irrigation work touched the fence line. That tells us which parts to bring.
2. 2
   On-site diagnostic. We test the transformer output, check the limit settings, watch a full open-close-open cycle, and note the cycle count if the board tracks one.
3. 3
   Written price. Before we replace anything, you get a flat price in writing. The cost to repair, the cost to replace, and the part numbers. You approve it or you don’t. No surprises either way.
4. 4
   The work. We use OEM Linear parts when warranty status or board compatibility calls for it, and quality aftermarket parts when they’re mechanically identical and priced lower. We tell you which is which.
5. 5
   Testing and documentation. We run the gate through at least five full cycles, set and record the limit positions, align the safeties, and photograph every adjustment.
6. 6
   Handover. You get a photo log of what was found, what was replaced, and what the gate cycles like now. We file the same record in our system under your address.

Every completed Linear job falls under our 365-Day Done Right Promise. If something we fixed fails within a year, we come back and make it right. No argument, no fee. You’ll also have the full written record to show any future technician.

Before

After

What Linear Gate Motor & Opener Costs in Frisco

Linear motor and opener work in Frisco is priced by the failure, not by the hour. Here’s what we see most often:

• Full linear swing-arm opener installed with new arm, board, and remote: $2,400 to $3,800 depending on gate weight and whether we’re reusing existing conduit.
• ACT-34B control board replacement: $450 to $700 installed and programmed.
• Battery backup replacement (pair): $180 to $320 including load testing.
• Limit switch reset and alignment: $150 to $250, including the photo record.
• Complete linear slide operator replacement: $3,200 to $5,500 installed, depending on chain versus belt and gate length.

What moves the price is the condition of the gate hardware behind the motor, not the motor itself. A worn hinge or a sagging gate makes any operator work harder and fail sooner, and we’ll tell you if that’s part of your problem. Estimates are free, and the price you approve is the price you pay. Call (940) 290-7996 for a written quote.

Why Frisco Homeowners Call Vance Gate Repair Frisco for Linear Work

We’re not tied to any single brand, so we’re not steering you toward a replacement you don’t need. Vance Gate Repair Frisco fixes Linear motors because that’s often the right call for the homeowner. When repair doesn’t make sense, we still quote a few options and let you decide.

We service nine major automation brands, so if you have a Linear opener now and decide later that a different drive system suits the property, we can handle that without subbing it out. LiftMaster, Mighty Mule, Ghost Controls, DoorKing - we maintain and repair all of it. Every visit includes a written price before work starts, a documented photo record when we leave, and the 365-Day Done Right Promise behind everything we touch. That’s the Haven Standard, and it’s how we’ve earned our reputation in Frisco since 2014.

FAQs