Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGhost Controls Access Control Installation: The Frisco Owner’s Guide
Ghost Controls access control installation in Frisco typically runs $275 to $475 for a keypad, push-button, or intercom unit matched to your existing Ghost Controls gate opener, installed and programmed same-visit in most cases. We stock the common Ghost Controls-compatible keypads and push-button stations on the truck, which means we can usually swap a failed unit the day you call. Most Frisco homeowners discover the problem when the keypad backlight stops responding, or the gate ignores an entry code that worked last week.
The number to call is (940) 290-7996. Tell us what the gate is doing, or what the keypad is not doing, and we will name the likely part and the price before we dispatch. Adrian Vance set that rule for every job: written price before anyone touches the gate.
Which Ghost Controls Models This Applies To
Ghost Controls has two main series you will see on Frisco driveways: the AXDP series (solar-friendly, battery-backed, common on single swing gates) and the Ghost Pro series (higher cycle rating, AC or solar, found on heavier swing and slide gates). The access control side is mostly universal across both: the keypad and push-button wiring taps into the EXIT and COM terminals on the control board, so the same keypad will generally work on an AXDP opener from 2018 and a Ghost Pro opener from 2022. The gotcha is the wire gauge and distance. Ghost Controls documentation calls for 16-gauge or heavier wire on any keypad run over 50 feet, and plenty of Frisco installs in older Starwood and Pearson Farms properties have thinner 20-gauge wiring from an older intercom that never worked correctly.
OEM Ghost Controls keypads are fine units and we install them, but we have also installed enough of them to know the mounting-plate plastic gets brittle after four or five Texas summers. For most homeowners we quote both the OEM part and a quality aftermarket equivalent, with the price difference stated in writing. We are an independent service provider, not a Ghost Controls dealer, which means we can install whichever part is genuinely the better fit for your configuration without a brand quota pulling us in one direction. We also stock parts for LiftMaster, Mighty Mule, and DoorKing, so if your opener was already a retrofit from another brand, we can trace what was actually installed rather than guessing.
Signs Your Ghost Controls Access Control Installation Is Failing
- The keypad lights up but the gate will not open from it. Usually this is a failed relay inside the keypad, not a programming issue. The control board is waiting for a dry-contact closure between EXIT and COM; if the relay inside the keypad has burned, the board never sees the command.
- The gate opens from a button inside the house but not from the keypad. That isolates the problem to the keypad side of the circuit. We start at the keypad and the wiring. In Frisco, the usual culprit on this symptom is a corroded connection inside the keypad housing after a wet spring, especially on north-facing posts that never fully dry.
- The keypad accepts some codes but not others. This one is almost always the keypad’s code memory going bad, not a user error. When one code slot still works and another does not, it is the unit, not the person pressing buttons.
- You hear a faint click but no gate movement. The keypad is closing its relay, but the control board is not responding. That points to a wiring or board-level issue rather than a keypad replacement. We check this before quoting a part, because replacing a working keypad will not fix a dead control board.
- The gate opens once, then refuses to respond for the next several tries. On solar-powered Ghost Controls setups this is often a low-battery condition at the control board. The access device is fine; the whole system is starving for power. A new keypad will not fix that, and we will tell you that before you spend money.
BeforeAfterReplacement Cost & What’s Included
In Frisco, a basic Ghost Controls-compatible replacement keypad installed by us will usually fall between $275 and $375 including the part, the labor, the programming, and the documentation. A push-button station or simple exit wand runs lower, around $180 to $250. A full replacement with a longer wiring run, a new post-mount box, or trenching a new cable across a driveway will push the top end closer to $475 to $600, because that is a wiring job as much as a parts job. Every price is written down and handed to you before we start. That is not a sales pitch; that is Haven Standard Clause 1, and it has applied to every one of the 22,000-plus gates we have worked on since 2014.
What you get for that price: the part matched to your opener, the install, the programming, a photo record of the wiring before and after, and the part number of what we installed. If the new unit fails within 365 days, we make it right at no charge under the Done Right Promise. No argument, no follow-up invoice, no “that part of the job is not covered” conversation.
DIY or Call Us?
Access control wiring on a Ghost Controls opener is low-voltage, and it is the least dangerous part of a gate system to work on. The risk is not really shock or injury; the risk is misdiagnosis. A homeowner will replace a keypad because it is the obvious part, then discover the real fault was a break in the wire fifteen feet underground, or a control board that stopped reading inputs. We have arrived at that scene many, many times, and the honest version is that the keypad was not the problem.
What you can safely check yourself: whether the keypad backlight comes on, whether there is visible corrosion at the keypad housing, and whether the same symptom happens from each entry device on the system. If one keypad is dead and every other button works, replacement is straightforward. If nothing opens the gate, call (940) 290-7996 and we will trace it. We would rather spend fifteen minutes on the phone telling you the likely cause for free than sell you a part that will not fix it.
FAQs
A Ghost Controls keypad on a Frisco gate post will typically last 3 to 5 years outdoors before the housing plastic degrades or the relay contacts fail, with failures running faster on unshaded western exposures. The electronics inside handle heat reasonably well; what fails first in our experience is the mounting plate and the relay, which is a $275 to $375 replacement installed by us. Call (940) 290-7996 for a written quote on your specific unit.
For a corroded connection or a broken wire inside the housing, yes; for a failed relay or a dead keypad brain, replacement is the honest recommendation and costs about the same as a repair once labor is factored. We will tell you which one you have before quoting anything, because that determination is free on the phone and should not require a service call.
A standard keypad or push-button replacement with no wiring repairs takes under an hour on-site, including programming all of your existing entry codes. If we find a broken wire run or a failed control board, that changes the scope and we will show you the revised written price before doing additional work.
Yes. Our Frisco trucks carry the common Ghost Controls-compatible keypads and push-button stations, plus the wiring connectors and housings that usually need replacing at the same time. If your system needs a specific OEM-only unit we do not stock, we order it and you get a firm install date, not a vague window.
Call Vance Gate Repair Frisco for Ghost Controls Access Control Work
If your Ghost Controls keypad, push-button, or intercom is failing, start by telling us what the gate is doing, and we will tell you what it costs to fix it. Call (940) 290-7996. A live person answers, any hour, and you will get a written price before we arrive, not after we have started. Free estimates, no obligation, no surprise invoice at the end. That has been the rule on every gate we have touched in Frisco since 2014, and it is not changing.
Written by Adrian Vance, Owner, Vance Gate Repair Frisco, serving Frisco and nearby areas.