Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Frisco, TX
Gate access control in Frisco usually means one of two things: a keypad or intercom that stopped talking to the operator, or an HOA requirement that’s about to outgrow what the original builder installed in 2005. We fix both, and we do it with a written price before any work starts. Most Frisco jobs we see involve gates on black-clay soil that’s moved the post enough to misalign the lock, the photo-eye, or the keypad mounting plate. Call (940) 290-7996 and a live person answers, any hour.
Why Frisco Homes Are Different
Frisco sits on Blackland Prairie clay that swells in wet springs and shrinks in summer drought. Gate posts heave and settle by inches, season after season. What started as a level swing gate in 2008 is now dragging on the latch side, and the keypad reads fine but the lock won’t release because the post moved a half inch. That’s the Frisco signature. We also see the summer heat and the freeze pattern: sustained 100°F days cook circuit boards and hydraulic pumps, while hard freezes crack solenoid housings and split conduit runs for access wiring. The 2000-2015 master-planned boom left thousands of HOA gates in Stonebriar, Starwood, and similar subdivisions running discontinued operator lines. When those fail, the repair often becomes a replacement quote, because the parts aren’t made anymore and the posts have drifted anyway.
Our Main Frisco Services
These are the three service pages Frisco homeowners search most. Each one covers that job in Frisco specifically, with local price ranges and the conditions that change the work here.
Gate Repair in Frisco
Swing and slide gates on clay soil need alignment work more than any other repair. A gate that scrapes, won’t close, or trips the operator’s obstruction sensor is usually a post-lean problem here, not a motor problem. We diagnose it by measurement, photograph the misalignment, and give you a written repair price before touching anything. Gate Repair in Frisco covers the full repair scope and what it costs.
Gate Installation in Frisco
Frisco HOAs have specific requirements for gate style, color, and sometimes vendor approval. We work within those requirements and spec the post depth for clay soil, not generic national tables. A gate installed to the right depth for Frisco ground won’t lean in three years. Gate Installation in Frisco explains the process, the HOA layer, and the written quote.
Gate Motor & Opener in Frisco
North Texas heat kills operator boards faster here than in most of the country, and Frisco’s freeze events add a second failure season. We service nine automation brands, so we can usually repair the motor on the gate instead of steering you to a replacement. Gate Motor & Opener in Frisco covers motor repair, replacement, and the brands we stock parts for.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Frisco
Frisco’s HOA communities built between 2000 and 2015 often run access control systems that are now 15 to 20 years old, with phone entry boards exposed to full Texas sun and keypads mounted on posts that have drifted on clay soil. The repair is rarely just the electronic board; it’s usually the board plus the post alignment plus the conduit run. We photograph what we find, write the scope, and hand you the price before work begins. Gate Access Control covers the full service across every brand we work on.
Keypad Entry
Signs you need it
The keypad beeps but the gate won’t move, or some codes work and others stopped working.
What it costs in Frisco
Keypad replacement in Frisco typically runs $175 to $410, including a weather-sealed unit rated for direct sun exposure.
How we do it
We test the keypad’s output at the operator terminals, replace or rewire the unit, and photograph the new connections and the post position.
Phone Entry
Signs you need it
The call rings through but the visitor can’t be heard, or the gate won’t open when the resident presses the button.
What it costs in Frisco
Phone entry repair in Frisco typically runs $160 to $400, depending on whether it’s a relay, a board, or a complete unit replacement.
How we do it
We check the phone line or cellular module, trace the relay output to the operator, and leave a printed diagram of what was changed.
Card Reader
Signs you need it
The reader flashes red for every card, or it reads cards but won’t trigger the operator.
What it costs in Frisco
Card reader replacement in Frisco typically runs $215 to $500, plus the cost of re-issuing credentials if the system changed.
How we do it
We bench-test the reader, verify the controller input, and photograph the new reader and wiring before we close the cabinet.
Video Intercom
Signs you need it
The screen shows a black image, the audio crackles, or the outdoor station won’t power on.
What it costs in Frisco
Video intercom repair in Frisco typically runs $235 to $570, with full unit replacement at the higher end.
How we do it
We test power at the outdoor station, check the video feed and door-release relay, and document every reading with photos.
What Gate Access Control Costs in Frisco
| Item | Typical range in Frisco |
|---|---|
| Keypad replacement | $175 - $410 |
| Phone entry repair | $160 - $400 |
| Card reader replacement | $215 - $500 |
| Video intercom repair | $235 - $570 |
Can you work with my HOA’s access control requirements in Frisco?
Yes. Most Frisco HOAs require uniformity in entry hardware, and we document the existing unit before quoting so the replacement matches what the HOA approved. The written quote lists the exact model we’re installing.
Do you fix access control on community entry gates in Frisco?
We do, including single-residence driveway keypads and shared community entry systems. The price is written before work starts, and the photo record goes to whoever manages the gate. Call (940) 290-7996 to schedule a free estimate.
Gate Parts & Welding in Frisco
When a Frisco gate post has moved on clay soil, the hinge side takes the load, and that’s where the metal fails first: cracked hinge plates, snapped weld points, bent rails on slide gates. Welding gets the gate back to square, but only if the post underneath is stable. We check the post first, then cut, weld, and photograph the repair. Gate Parts & Welding covers the full parts and welding scope.
Hinge Replacement
Signs you need it
The gate sags or scrapes on the latch side, and the hinges show visible cracks or movement at the weld points.
What it costs in Frisco
Hinge replacement in Frisco typically runs $210 to $450, depending on hinge size and whether a post shim is needed.
How we do it
We cut the old hinge, weld the new one in place, re-hang the gate, and photograph the new weld with the gate level again.
Post Replacement
Signs you need it
The post leans visibly, the gate drags, and adjusting the hinge side no longer levels the gate.
What it costs in Frisco
Post replacement in Frisco typically runs $375 to $950, including digging below the clay movement line and setting the new post in concrete.
How we do it
We pull the old post, set the new one deeper than the original, re-hang the gate, and document the whole process in photos.
Rail Repair
Signs you need it
The gate binds halfway through its travel, or the rail shows a bow, a crack, or a worn section where the rollers run.
What it costs in Frisco
Rail repair in Frisco typically runs $265 to $675, including straightening and re-welding broken sections or replacing a full rail run.
How we do it
We inspect the rail straightness against the post line, cut out the bad section, weld new steel in, and photograph the finished run.
Gate Rollers
Signs you need it
The gate shudders or jerks when it moves, and the rollers show flat spots or wobble on their bearings.
What it costs in Frisco
Gate roller replacement in Frisco typically runs $185 to $390, including a check of the rail and all carriage bolts.
How we do it
We replace the worn rollers, adjust the gate to sit square on the rail, and photograph each new roller after torquing the bolts.
What Gate Parts & Welding Costs in Frisco
| Item | Typical range in Frisco |
|---|---|
| Hinge replacement | $210 - $450 |
| Post replacement | $375 - $950 |
| Rail repair | $265 - $675 |
| Gate roller replacement | $185 - $390 |
Can you weld my gate on site in Frisco?
Yes, for most residential gate work we weld on site, including hinge plates, rail sections, and picket repairs. We bring a mobile welding rig to the property and photograph every weld before cleanup.
Do you weld ornamental iron gates in HOA neighborhoods?
Yes, and we match the weld finish to the existing gate so it passes HOA inspection. The written quote includes the specific material and finish we’re using. Call (940) 290-7996 for a free estimate.
Brands We Service in Frisco
We service LiftMaster, FAAC, BFT, and Mighty Mule operators, among the nine major brands we support. Parts for the most common models are stocked locally, which keeps most repair turnaround under 48 hours. Our brands page lists the full lineup.
Pricing for Gate Repair in Frisco, TX
| Service | Typical range in Frisco |
|---|---|
| Keypad replacement | $175 - $410 |
| Phone entry repair | $160 - $400 |
| Card reader replacement | $215 - $500 |
| Video intercom repair | $235 - $570 |
| Hinge replacement | $210 - $450 |
| Post replacement | $375 - $950 |
| Rail repair | $265 - $675 |
| Gate roller replacement | $185 - $390 |
What pushes a Frisco price up is almost always the post. If clay movement has shifted a post, the access control repair or hinge work has to account for leveling the gate first, and that’s part of the written quote, not a surprise line item. Every price is handed over before work starts, under Haven Standard Clause 1.
Neighborhoods We Serve in Frisco
We dispatch crews to every corner of Frisco, from Stonebriar and Starwood to the newer subdivisions east and north. Typical response for a repair call is under 24 hours, with many jobs scheduled same week.
- Stonebriar
- Starwood
- Plantation Resort
- Legacy
- Griffin Parc
Service Area - Cities Near Frisco
We also serve the communities around Frisco, including Prosper, TX, Little Elm, TX, Celina, TX, and The Colony, TX. Dispatch runs from the brand’s Dallas-Fort Worth office with local Frisco crews.
Serving Frisco, TX - Our Local Coverage Area
We’re based in the Frisco area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Frisco
Most Frisco calls get a crew within 24 hours, and emergency service is available any hour. A live person answers the phone at any time, so you’ll know the schedule before you hang up. Call (940) 290-7996 to book.
It depends on the neighborhood. Some Frisco HOAs require approval before any exterior gate change; repairs to existing gates usually move faster. We can provide the documentation your HOA asks for, including the written quote and a photo record.
We come to you, for every repair and most welding jobs. The estimate is free, the price is written before work starts, and you get a full photo record of what was found and what was done.
For gate access control, parts, welding, or any gate issue in Frisco, call (940) 290-7996 for a free estimate. A live person answers, the price is written before work begins, and the work is documented with photos when we leave.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Frisco Customers Say
"They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C."Good work on a long driveway gate. Arrived when they said, finished when they said."
- Sofia E."Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R.